Horizon treadmill remains to be one of the most popular fitness equipment, whether used in the gym or at home.
Like any other complicated machines, Horizon products can malfunction in a variety of ways. If your Horizon T202 treadmill doesn’t start, you will need to troubleshoot the possible cause.
Let’s review the most troubleshooting methods to follow in order to find out why your Horizon T202 treadmill won’t turn on before calling the manufacturer or a repair person.
Without further ado, let’s get right into it!
Why Is My Horizon T202 Tread Not Working?
There are multiple reasons for why a Horizon T202 Treadmill won’t turn on and stop unexpectedly.
The problem might be something you can fix yourself, ranging from simple possibilities such as power supply problems, the installation does not meet Horizon T202 electrical power requirements, or the safety key is not connected properly. To more complex possibilities, such as motor controller problems.
The following troubleshooting guides will help you identify and fix your Horizon T202 treadmill problem.
Horizon T202 Treadmill Won’t Turn On – Troubleshooting Guides
1. Check the outlet
Always check if your power cable is connected properly to the outlet and your T202.
A Horizon treadmill won’t turn on if there is a loose connection. The loose connection usually occurs if the power cable is not properly plugged into an electric outlet or the power cable is not properly connected to the power brick.
Make sure the electrical outlet has power by plugging a small appliance into it to see if it works.
If the appliance doesn’t power, reset the house circuit breaker to restore power to the outlet.
If the Tread is still not receiving power, plug the treadmill to another outlet. Make sure not to use a power strip, power adaptor, or an extension cord.
Next, make sure that your Horizon T202 tread is plugged into an outlet that meets its power requirements.
The power requirements are: 100-125vac, 50-60Hz, 15 amp “dedicated circuit”.
Also, ensure that the Tread is not plugged into a GFCI outlet.
2. Check the power cord
If the electrical outlet works fine and the outlet meets the power requirements of your Horizon T202 tread, unplug and turn off Horizon treadmill to check the power cord for damage.
Make sure the cord is connected properly to both the electrical outlet and the Tread’s deck.
Next, check all wires between the power cord connection and the motor control board. Reconnect any loose wires and repair any broken ones.
If the cord has been damaged then you may need to replace it with a new one.
3. Check the power switch
If your Horizon T202 Tread is not receiving power, check if the power switch was tripped.
If so, Horizon advises to wait five minutes and then press the switch back to the Reset position.
Next, through the use of a multimeter, check the continuity of the power switch.
Replace the power switch if the meter measures no continuity through the power switch with the power switch turned on.
Turn on Horizon treadmill and check if it starts. If the tread still doesn’t run, move to the next troubleshooting step.
4. Check the safety key connection
If your Horizon T202 tread won’t turn on, make sure the safety key is fully inserted in the console. The treadmill won’t run if the safety key isn’t in the console.
Make sure that your safety key is properly connected while the Tread is in use.
The area surrounding the safety key and safety key opening should be kept dry and free from moisture.
Moreover, if the safety key, safety key opening, or surrounding area is exposed to any sort of liquid, it’s quite crucial to dry these areas immediately.
5. Check the motor board
If the console lights up, but the T202 won’t start, then you need to inspect the motor controller board. Loose wires under the motor hood or in the console can also cause your treadmill not to start.
Therefore, you need to remove the motor cover. Look around for any obvious damage, burns, loose or broken wires.
Next, use a multimeter to see if you are getting the correct voltage coming from the console to the motor control board.
If you get 120VAC from the console and from the board, the board is working fine.
However, if you have voltage from the console but not from the board, then you have an issue with the controller board.
Check all wires between the power cord connection and the motor control board. Reconnect any loose wires and repair any broken wires.
If wiring that connects power to the motor control board is okay, check the wiring between the motor control board and the console display. Replace any loose wires and repair any broken wires.
If the wires between the control board and the display are okay, then you either have a bad motor control board or a failed console display that is preventing the Horizon T202 from powering up.
If none of the above fixes work, then you need to contact the Support Team of your treadmill. They will help you diagnose the problem and offer solutions.
If your treadmill is still under warranty, the manufacturer may cover the cost to repair your machine.
However, if you attempt to fix the tread yourself while it is under warranty, then you may void the warranty.
In this case, only perform the troubleshooting tips recommended by your manufacturer.
If your Horizon T202 tread won’t turn on, there are a few things you can do to fix it.
First of all, make sure that the machine is properly plugged into a power source that meets Horizon T202 electrical power requirements.
Check the power cord to see if it is connected properly to both the electrical outlet and the Tread’s deck.
Also ensure the safety key is connected properly while the Tread is in use.
You may need to replace the motor controller board if it gets enough power but doesn’t work appropriately.