The number one thing you must be looking for after your brand new NordicTrack 9.9 elliptical has just arrived, or after you disassemble a NordicTrack elliptical to move it into your new place, is how to assemble this elliptical together.
Well, let’s jump into today’s step by step guide to NordicTrack 9.9 elliptical assembly. As well as what tools to make sure you have before you start the assembling process.
Without further ado, let’s get right into it!
Tools Needed To Assemble NordicTrack 9.9 Elliptical
The first step before you start the elliptical assembling process is to gather all the necessary tools.
You don’t want to go through with one step, then realize that something is lacking.
In order to assemble a NordicTrack 9.9 Elliptical machine, you are going to need the following tools:
- Phillips head screwdriver.
- 6MM Allen Wrenches.
- Hammer.
- Pliers.
- Box Cutter.
- Socket.
In addition to the required tool, a second person to assist you through the assembling process is also going to be necessary here.
The assembling process is definitely a two-person job, so make sure you have a friend or your partner as an assistance in order to safely and successfully put the machine together.
NordicTrack 9.9 Elliptical Assembly – Step By Step Guide
Before you start the NordicTrack 9.9 assembling process, select the area where you are going to set up and operate your machine. The location must be on a hard, level surface.
Also be sure that the workout space you are utilizing has adequate height clearance, taking into consideration the height of the user and the maximum incline of the elliptical machine fully engaged.
Head to my.nordictrack.com on your computer and register your product.
This will activate your warranty and ensure priority customer support if assistance is ever needed.
If you do not have internet access, call Customer Care and register your product.
Step 1: Install the leg stabilizers
With your assistance’s help, place some of the packaging material under the rear of the frame.
If there are shipping supports attached to the rear of the Frame, remove the screws from the shipping supports, and discard the screws and the shipping supports.
Have the second person hold the Frame to prevent it from tipping while you complete this step. After you identify the rear leg stabilizer, attach it to the Frame with two M10 x 112mm Screws.
Remove the packing materials from under the rear of the Frame.
Then, press the Cover Mounts on the underside of the Rear Stabilizer Cover into the Rear Stabilizer.
Repeat this step with the front leg stabilizer to attach the front stabilizer to the frame.
Step 2: Install the upright
Have a second person hold the Upright on the Frame. Secure the upright to the Frame with four M10 x 25mm Screws, but do not fully tighten the screws yet.
Next, locate the wire tie in the lower end of the Upright. Attach the wire tie to the Main Wire, then pull the upper end of the wire tie until the Main Wire is routed through the Upright.
Step 3: Attach the upper body legs
Using a plastic bag to keep your fingers clean, apply some of the included grease to the axle on the right side of the Upright.
Next, slide a Pivot Spacer onto the right side of the Upright. Then, identify the Right Upper Body Leg, and slide it onto the right side of the Upright. Attach it with an M8 x 13mm screw and an M8 x 28mm Washer.
Repeat this step for the Left Upper Body Leg.
Step 4: Attach the pedal arms
Insert the Right Pedal Arm into the Right Upper Body Leg and into the Right Roller Arm.
Next, attach the Right Pedal Arm to the Right Roller Arm with an M8 x 20mm Flat Head screw and a Retainer.
Make sure that the flat side of the Retainer is facing the Right Roller Arm.
Repeat this step for the Left Pedal Arm.
After you apply grease to a Pedal Arm Axle, insert it into the Right Upper Body Leg and the Right Pedal Arm.
Next, slide an M8 x 22mm Washer onto an M8 x 13mm Screw, and tighten the screw a few turns into the Pedal Arm Axle.
Then, tighten the Pedal Arm Axle and the M8 x 13mm screw at the same time.
Repeat this step on the left side of the elliptical.
Last but not least, identify the Right Leg Inner Cover, and insert it through the Right Upper Body Leg.
Next, identify the Right Leg Outer Cover, and press it onto the Right Leg Inner Cover.
Attach the Right Leg Outer and Inner Covers to each other with an M4 x 16mm Screw.
Repeat this step on the other side of the elliptical.
Step 5: Install the console
Tighten the four Screws attaching the upright to the frame. Then untie and discard the wire tie on the Main Wire.
While a second person holds the Console near the Upright, plug the Main Wire and the Pulse Wire into the receptacles on the Console.
The connectors on the Wires should slide easily into the receptacles and snap into place.
If a connector does not slide easily into a receptacle, turn the connector and try again.
If you do not connect the connectors properly, the Console may become damaged when you use the elliptical.
Insert the excess wire into the Upright or into the Console. Then attach the Console to the Upright and secure it with four M4 x 16mm screws.
The next step is to attach the console covers. Start by attaching the rear console Cover to the Upright with two M4 x 16mm Screws. Then attach the front cover to the rear console cover with another two M4 x 16mm Screws.
Lastly, attach the accessory Tray to the Upright with two M4 x 16mm Screws.
The next step is to attach the console covers. Start by attaching the rear console Cover to the Upright with two M4 x 16mm Screws. Then attach the front cover to the rear console cover with another two M4 x 16mm Screws.
Attach the accessory Tray to the Upright with two M4 x 16mm Screws.
Last but not least, attach the Tablet Holder to the Console with four Tablet Holder Screws. Start all the Tablet Holder Screws, and then tighten them.
Step 6: Install the upper body arms
First, orient the Lower Tray Cover, and attach it to the right side of the Accessory Tray with two M4 x 16mm Screws.
Repeat this step on the other side of the elliptical.
Next, identify the Right Upper Body Arm, and insert it into the Right Upper Body Leg.
Then attach it with two M8 x 45mm Bolts and two M8 Locknuts. Make sure that the Locknuts are in the hexagonal holes.
Repeat this step for the Left Upper Body Arm.
Step 7: Attach the shield covers
Orient the Front Shield Cover and the Center Shield Cover around the Upright. Then, attach them to each other with two M4 x 16mm Screws.
Press the Front Shield Cover and the Center Shield Cover onto the Left and Right Shields.
After you finish with the assembling process and ensure all all screws are tight, turn on your NordicTrack elliptical and test the elliptical by running on it for a few moments before use to make sure everything is working properly.
Conclusion
This guide will walk you through the NordicTrack 9.9 elliptical assembly process. The assembly process is broken down into easy to follow steps in order to safely and successfully start using your NordicTrack cross trainer.
Step 1: Install the leg stabilizers
Step 2: Install the upright
Step 3: Attach the upper body legs
Step 4: Attach the pedal arms
Step 5: Install the console
Step 6: Install the upper body arms
Step 7: Attach the shield covers
Make sure to lubricate NordicTrack elliptical machine moving parts to get things running smoothly.
FAQ
how long does it take to assemble a NordicTrack 9.9 elliptical?
The assembling process of a NordicTrack 9.9 elliptical is not complicated, but it does require some time and patience.
It usually takes 60-to-90 minutes to assemble a 9.9 elliptical machine.
