The Complete Guide To Schwinn 411 Elliptical Assembly

The number one thing you must be looking for after your brand new Schwinn 411 elliptical has just arrived, or after you take apart a Schwinn elliptical to move it into your new place, is how to assemble this elliptical together.

Well, let’s jump into today’s step by step guide to Schwinn 411 elliptical assembly. As well as what tools to make sure you have before you start the assembling process.

Without further ado, let’s get right into it!

Tools Needed To Assemble Schwinn 411 Elliptical

picture of schwinn 430 elliptical machine from my home gym

The first step before you start the elliptical assembling process is to gather all the necessary tools.

You don’t want to go through with one step, then realize that something is lacking.

In order to assemble a Schwinn 411 Elliptical machine, you are going to need the following tools:

  • Phillips head screwdriver.
  • 6MM Allen Wrenches.
  • Hammer.
  • Pliers.
  • Box Cutter.
  • Socket.

In addition to the required tool, a second person to assist you through the assembling process is also going to be necessary here.

The assembling process is definitely a two-person job, so make sure you have a friend or your partner as an assistance in order to safely and successfully put the machine together.

Schwinn 411 Elliptical Assembly – Step By Step Guide

Before you start Schwinn 411 assembling process, select the area where you are going to set up and operate your machine. The location must be on a hard, level surface.

Also be sure that the workout space you are utilizing has adequate height clearance, taking into consideration the height of the user and the maximum incline of the elliptical machine fully engaged.

proform elliptical machine picture from my garage gym

Step 1: Attach the rail assembly to the frame

First, install the four provided levelers to the bottom of the rail assembly before attaching it to the frame.

Then, push the rail assembly towards the frame and slowly slide it under the rail assembly plates. Secure the rail assembly screws to the frame using the provided 6mm Allen Wrench.

Step 2: Install the console mast

Start by placing the console mast on the top of the frame.

The bottom of the console mast has one cable sticking out, while the top part has two cables.

Connect the console mast cable to the frame cable. Then, push the cables towards the inside of the frame and lower the console mast matching the square end plate with the square end plate on the frame.

Next, secure the console mast to the frame and fully tighten the screws using the provided 6mm Allen Wrench.

Step 3: Attach the legs

picture of schwinn 430 elliptical machine from my home gym

Begin this step by placing the left leg at the bottom left side of the assembly.

The front portion of the leg slides into the rod on the side of the frame, while the back portion goes over the rail assembly.

Secure the left leg using one part A Screw, one part G lock washer, one part G wide washer, and one part F wave washer.

Slide the wave washer into the rod before attaching leg. After set the left leg in place.

Next, place the wide washer first, followed by the lock washer and the screw. Fully tighten the screw using the provided 6mm Allen Wrench.

Repeat these steps for the right leg.

Step 4: Attach the Arm Pivot Rod & Lower Handlebar Arms

Begin by identifying the left lower handlebar arm, and slide it onto the right side of the pivot rod.

Attach it to the arm pivot rod using M8 x 13mm screw and an M8 x 28mm Washer. Fully tighten the screw using the provided 13mm Wrench.

Repeat this step for the right lower handlebar arm.

Step 5: Attach the pedals

The left pedal attaches to the bottom of the lower handlebar arm and to the back end of the left leg.

Before attaching the pedal, insert one part F wave washer into the rod located underneath the pedal. Push the washer into place.

Next, pivot the pedal and slide it into place. Secure it to the left lower handlebar arm using one Part A screw, one part G lock washer, one part C wide washer, and one part H pivot sleeve (the pivot sleeve has a keyway that must match the keyway one the lower handlebar arm).

Fully tighten the screw using the provided 6mm Allen Wrench.

Next, secure the pedal to the left leg using one part A screw, one part G lock washer, and one part C wide washer.

Repeat these steps for the opposite side to attach the right pedal as previously shown.

Step 6: Attach the upper handlebar arms

picture of schwinn 430 elliptical machine from my home gym

Locate the left upper handlebar arm, and place it on the left side of the assembly.

The arm has hardware located on the bottom. They must be removed before attaching the arm.

Next, slowly insert the bottom end of the upper handlebar arm onto the open end of the lower handlebar arm.

Adjust the handlebar and make sure the bottom holes match the holes on the lower handlebar arm. Fully secure the left upper handlebar arm using the previously removed hardware.

Repeat this step for the Left Upper handlebar Arm.

The next step is to attach the handlebar shrouds. Start by locating one outer handlebar shroud and one part eye screw.

Place it on the left upper handlebar arm, then push the outer shroud into place matching the hole on the shroud with the hole on the handlebar arm.

Repeat the same on the opposite side and secure the inner handlebar shroud as previously shown.

Finally, repeat these steps for the right side to attach the right handlebar arm shroud.

Step 7: Install the console

Start off by removing hardware located on the back of the console, and set them aside for now.

While a second person holds the Console near the static handlebar, plug the cables sticking out of the static handlebar into the receptacles on the Console. 

The connectors on the Wires should slide easily into the receptacles and snap into place. 

If a connector does not slide easily into a receptacle, turn the connector and try again. 

If you do not connect the connectors properly, the Console may become damaged when you use the elliptical. 

Then attach the Console to the Upright and secure it with four M4 x 16mm screws.

picture of schwinn 430 elliptical machine from my home gym

After you finish with the assembling process and ensure all all screws are tight, turn on your Schwinn elliptical and test the elliptical by running on it for a few moments before use to make sure everything is working properly.

Conclusion

This guide will walk you through the Schwinn 411 elliptical assembly process. The assembly process is broken down into easy to follow steps in order to safely and successfully start using your Schwinn cross trainer.

Step 1: Attach the rail assembly to the frame

Step 2: Install the console mast

Step 3: Attach the legs

Step 4: Attach the Arm Pivot Rod & Lower Handlebar Arms

Step 5: Attach the pedals

Step 6: Attach the upper handlebar arms

Step 7: Install the console

Make sure to lubricate Schwinn elliptical machine moving parts to get things running smoothly.

Scroll to Top