The number one thing you must be looking for after your brand new Sunny magnetic elliptical bike SF-e3912 has just arrived, or after you disassemble your Sunny SF-e3912 elliptical to move it into your new place, is how to assemble this elliptical together.
Well, let’s jump into today’s step by step guide on Sunny Health And Fitness Elliptical SF E3912 Assembly. As well as what tools to make sure you have before you start the assembling process.
Without further ado, let’s get right into it!
Sunny Magnetic Elliptical Bike SF-E3912 Assembly
The first step before you start the elliptical assembling process is to gather all the necessary tools.
You don’t want to go through with one step, then realize that something is lacking.
In order to assemble Sunny elliptical sf-e3912, you are going to need the following tools:
- Phillips head screwdriver.
- 6MM Allen Wrenches.
- Hammer.
- Pliers.
- Box Cutter.
- Socket.
In addition to the required tool, a second person to assist you through the assembling process is also going to be necessary here.
The assembling process is definitely a two-person job, so make sure you have a friend or your partner as an assistance in order to safely and successfully put the machine together.
How To assemble Sunny Health And Fitness Elliptical SF-E3912 – Step By Step Guide
Before you start the Sunny SF-E3912 assembling process, select the area where you are going to set up and operate your machine. The location must be on a hard, level surface.
Also be sure that the workout space you are utilizing has adequate height clearance, taking into consideration the height of the user and the maximum incline of the elliptical machine fully engaged.
STEP 1: Install the leg stabilizers
With your assistance’s help, place some of the packaging material under the rear of the frame.
If there are shipping supports attached to the rear of the Frame, remove the screws from the shipping supports, and discard the screws and the shipping supports.
Have the second person hold the Frame to prevent it from tipping while you complete this step. After you identify the rear stabilizer, attach it to the Main Frame with 2 Bolts that were removed.
Remove the packing materials from under the rear of the Frame.
Repeat this step with the front leg stabilizer to attach the front stabilizer to the frame.
STEP 2: Install the tension controller and the handlebar post
Have a second person hold the Handlebar post on the Frame. Connect the Lower Sensor Wire to the Upper Sensor Wire, and then connect Tension Hook with the Tension Cable.
Make sure the Tension Controller is set at resistance level 1 before you connect the Tension Cable. This will ensure the wires are at their longest reaching point.
Next, insert the Handlebar Post into the post of the Main Frame with 6 Spring Washers, 6 Washers, and 6 Bolts.
Then, place the Front Plastic Cover into position.
STEP 3: Install the Upper Swing Bar
Attach the Left Upper Swing Bar to the Left Lower Swing Bar with 2 Bolts and 2 Nylon Nuts.
Repeat this assembly step to the Right side.
First you need to remove the 2 Wave Washers, 2 Washers, 2 Spring Washers, and 2 Bolts from the Axis.
Attach the Left & Right Lower Swing Bars and the Axis to the Handlebar Post with the hardware that were removed.
Attach the Left & Right Lower Swing Bars to the Left & Right Pedal Support Bars with 2 Nylon Nuts, 2 Washers, and 2 Bolts. Tighten and secure with Allen Wrench and Spanner.
Attach the Left & Right Pedal Support Bars to the Main Frame with 2 Washers, 2 Spring Washers, 2 Bolts, and 2 Tubes.
STEP 4: Install the Pedals
Secure the Pedals to the Pedal Support Tube using Hex Bolt, Flat Washer and Nylon Nut.
Repeat this assembly step to the Left side.
STEP 5: Install the Handlebar
Attach Handlebar to the Handlebar Post with 3 Spring Washers, 3 Washers, and 3 Bolts. Tighten and secure with Allen Wrench.
Insert the Hand Pulse Cable into the front hole of Handlebar Post and pull up the Hand Pulse Cable from the top hole the Handlebar Post.
STEP 6: Attach the Plastic Covers
Remove 2 Screws from the Left & Right Pedal Support Bars. Attach the M Plastic Cover to the Left & Right Pedal Support Bars with 2 Screws that were removed.
Remove 2 Screws from the Lower Swing Plastic Covers. Attach the Lower Swing Plastic Covers to the Left & Right Lower Swing Bars with 2 Screws that were removed.
Remove 2 Screws from the Left & Right Upper Central Shaft Plastic Covers. Attach the Left & Right Upper Central Shaft Plastic Covers to the Left & Right Upper Swing Bars with 2 Screws that were removed.
Remove 4 Self-tapping Screws from the Left & Right Axis Plastic Covers and one from the Handlebar Post. Attach the Left & Right Axis Plastic Covers to the Handlebar Post by using the Screws that were removed.
STEP 7: Install the Console
Remove 4 Screws from the back of the Computer.
Connect the Upper Computer Cable and Hand Pulse Cable to the wires of Computer.
Attach the Computer onto the top end of Handlebar Post using 4 Screws that were removed. Tighten and secure with Allen Wrench.
Remove 2 Screws from the Handlebar Post. Attach the Front /Rear Handlebar Post Cover to the Handlebar Post using Screws you just removed.
Conclusion
The assembling process of Sunny elliptical SF-e3912 is not complicated, but it does require some time and patience.
It usually takes 60-to-90 minutes to assemble the SF-e3912 elliptical machine.
The process has been broken down into easy to follow steps in order to safely and successfully start using your Sunny magnetic elliptical machine.
STEP 1: Install the leg stabilizers
STEP 2: Install the tension controller and the handlebar post
STEP 3: Install the Upper Swing Bar
STEP 4: Install the Pedals
STEP 5: Install the Handlebar
STEP 6: Attach the Plastic Covers
STEP 7: Install the Console
